VINCENT SERIES "A" PARTS



F24/1.5 - SERIES "A" PROP STAND, EXTENDED 1 1/2"- $150

New version has a 5/8" steel hole with a 1/2" ID hard bronze bushing installed. Can be used with a 5/8" (remove bushing), 9/16" (drill out bushing), or a 1/2" mounting shaft.

1 1/2" longer to achieve proper lean angle. Shown on left is a stock original.

Heat treated 4140 chromoly steel to Rockwell 40C.



FF31AS - BRAMPTON Series A Handlebar Riser, 1" - $75 each.

2 used on Series A Fork Upper Triple Tree. For 1" handlebars.

Heat Treated 4140 to Rockwell 40C.



FF31A - BRAMPTON Series A Handlebar Riser Cap, 1" - $30 each

2 used on Series A Fork Upper Triple Tree Riser. For 1" handlebars.

Heat Treated 4140 to Rockwell 40C.



FT188A - BRAMPTON "A" Side Damper Wing Nut - $30

5/16" x 26 CEI threaded hole. 2.7" overall length.

Heat Treated 4140 to Rockwell 40C.



PR50-194X - Series "A" TWIN Kickstarter with Footpiece, CHROME. $400. In stock.

PR50-194X - Series "A" TWIN Kickstarter with Footpiece, cadmium plated. $340 in stock.

Suitable for "A" Singles and some other pre-WW2 bikes with Burman gear boxes.

Limited production. Heat Treated 4140 to Rockwell 40C.



PR50-195X-Mark 1 - Series "A" Kickstarter Footpiece.

Limited production. Threaded 9/16" x 20 tpi BSF.

Heat Treated 4140 to Rockwell 40C.



VINCENT SERIES "A" PARTS COMMON to SERIES "B"



F55B - Balance Beam, Series "B" - $80

Brampton Twins and Singles.



FT200 - BRAMPTON LOWER RIGHT LINK- $95

1/2" CEI RH thread.

Heat treated 4140 chromoly steel to Rockwell 40C.



FT213L - BRAMPTON LOWER LEFT LINK- $70

1/2" CEI LH thread.

Heat treated 4140 chromoly steel to Rockwell 40C.



FT213L - BRAMPTON UPPER LEFT LINK- $55

3 3/8", 7/16" CEI LH thread.

Heat treated 4140 chromoly steel to Rockwell 40C.



FT213R - BRAMPTON UPPER RIGHT LINK- $55

3 3/8", 7/16" CEI RH thread.

Heat treated 4140 chromoly steel to Rockwell 40C.



FT220L Friction Plate, Left Hand - series B- $35

Brampton Twins and Singles. Polished and Chromed. Photo isn't very good but the parts are nicely plated.



FT220R Friction Plate, Right Hand - series B- $35

Brampton Twins and Singles. Polished and Chromed. Photo isn't very good but the parts are nicely plated.



FT227C - BRAMPTON HANDLE BAR CAP SCREWS- $15 ea. chrome plated steel, FT227 - $12 ea. cadmium plated steel.

5/16" CEI. I'm not a fan of stainless steel screws. Yes, I do make the Saint Christopher Medal.

Heat Treated 4140 chromoly steel to Rockwell 40C.



FT229 - BRAMPTON BEARING CONE RETAINER- $60

One of the very few fully machined parts I will ever manufacture. No one else is making them and they are essential in supplying a complete Brampton Fork Assy. The bearing actually fit in these. No additional fitting required.



FT232AS - BRAMPTON STEERING DAMPER FOOT - $85

All steel construction. Heat treated 2 3/8" cone shaped washer (which rotates freely).

Another one of those parts that are not available from any source we could find. Oh, and these fit.



FT233 Damper Spring Blade - series B - $20

Brampton Twins and Singles. These are Parkerized steel, OEM parts were painted black.



FT240 - STEERING DAMPER ROD - series B - $20

FT241 - STEERING DAMPER LOCKNUT - series B - $20

Rods are 10+ inches long, Parkerized 4140 steel.

Nuts are chromed steel.

Brampton Twins and Singles.



http://www.mikesvincentparts.com/